Turn Signal Load Equalizer

Bagger Nation has many different custom taillights options.  If your Harley is an early model bike then you may need a Load Equalizer to adjust the load the old incandescent bulbs used to a lower power requirement that L.E.D.s & C.O.B.s need.

 

MORE DETAILS BELOW!

SKU: PYO:BLIK | PYO:BLIK-10 | PYO:BLIK-14 | PYO:BLIK-CVO-1 Categories: , , , , Tags: , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , ,

Description

Turn Signal Load Equalizer

By Badlands

 

Stock flasher relays on motorcycles are designed to blink twice as fast as normal when a bulb is burned out to alert the driver of this condition.  L.E.D.s consume so little power compared to the stock bulbs that the flasher relay thinks that a bulb is burned out when LEDs are used in place of stock bulbs.  If you have replaced your stock turn signals with L.E.D.s and your turn signals flash too fast or do not flash at all, you will need to add an equalizer or replace your flasher relay.  These Load EQ’s are (in most cases) Plug N Play so that you can service your bike.  These are a must-have for any custom project.  Please read the Spec sheet for each Load EQ to find the one for your project.

NOTE:  The load equalizer is not necessary for 2014 and later models.
NOTE: The Badlands Load Equalizer will regulate the flashing sequence at a consistent rate.
NOTE: Load EQ’s kits will vary by year.  Make sure you read and understand the fitment!

Additional information

Weight 2 lbs
Dimensions 11 × 7 × 5 in
Option

LE-03, LE-03-A, LE-03-SRCVO, LE-03-SR, ILL-01, ILL-SD
Please select a variation
Specifically designed to work with OEM alarm systems Can be used with most custom turn signal setups (including halogen and LED signals) Module is solid-state -- produces absolutely no heat so it is OK for parade use Fits H-D models 91 that have self-canceling turn systems Made in the U.S.A.
Works specifically with H-D OEM alarm systems (TSSM) or H-D turn signal module (TSM) Stops erratic blinking of turn signals Can be used with most custom turn signals (including halogen and LED signals) Module is solid-state waterproof design OK for parade use; does not produce excess heat so emergency flashers may be used for an extended amount of time For use on models with self-canceling turn signals Made in the U.S.A.
Works specifically with H-D OEM alarm systems (TSSM) or H-D turn signal module (TSM) Stops erratic blinking of turn signals Can be used with most custom turn signals (including halogen and LED signals) Module is solid-state waterproof design OK for parade use; does not produce excess heat so emergency flashers may be used for an extended amount of time For use on models with self-canceling turn signals Made in the U.S.A. Fitments: FLHXSE/FLTRXSE - 10-13 Included Items: (1) Load equalizer 3 module with six pin male and female connectors, and three mounting holes (2) Cable ties Instructions
Works specifically with H-D OEM alarm systems (TSSM) or H-D turn signal module (TSM) Stops erratic blinking of turn signals Can be used with most custom turn signals (including halogen and LED signals) Module is solid-state waterproof design OK for parade use; does not produce excess heat so emergency flashers may be used for an extended amount of time For use on models with self-canceling turn signals Made in the U.S.A. NOTE: For FLHX/FLTRX 10-13 NOTE: Not for CVO Dresser models
Get double duty from stock or custom turn signals - module puts them to use as running and brake lights, while retaining turn signal capabilities Run even the smallest lights or a minimum of two lights only thanks to the built-in load equalizer Comes complete with easy-to-follow instructions, wiring and connectors Made in the U.S.A.
Hard wired installation for custom fit Allows for three separate LED turn signal lights installed per side on the rear of the bike to flash sequentially (1st LED on/off, 2nd LED on/off, 3rd LED on/off and then the sequence repeats) LEDs will also perform brake and running light functions Includes color-coded replacement rear fender harness and installation instructions Built-in load-equalizer prevents rapid flashing Included Items: (1) Sequential module w/wiring harness (2) Wiring harnesses W/(1) 4 pin male connector (4) 12" Black wires (2) Black cable ties (12) 1-1/2" Shrink sleeves (2) 30" Shrink tubes Instructions

Installation Instructions

LE-03-Hardwire-Plug-n-Play.pdf
ILL-01-All-Plug-n-Play-Models.pdf

You may also like…

Related products